Sorry, you need to enable JavaScript to visit this website.

Unable To Get Resolutions Higher Than 1024X768 on Fedora 19 64 Bit

3 posts / 0 new
Vaibhav Bhardwaj's picture
Starter
Vaibhav Bhardwaj

Aug 31, 2013 - 11:18pm

  • Dear All,

    I tried to install intel-linux-graphics-installer-1.0.2-10.1.x86_64 on my freshly formatted system with Fedora 19 64 bit installed.

    The installer went well without any errors or warnings, prompted for a reboot.

    After the reboot I was unable to get the any resolutions higher than 1024 x 768. When I boot my system in Windows 7, I can easily set the resolution to 1280x1024 or even higher (as I've installed Intel Drivers there). This means that the higher resolutions are supported, but I'm unable to get them in Fedora 19.

    My System configurations are as follows:

     

    $ uname -a

    Linux localhost.localdomain 3.10.9-200.fc19.x86_64 #1 SMP Wed Aug 21 19:27:58 UTC 2013 x86_64 x86_64 x86_64 GNU/Linux

     

    $ lspci | grep VGA

    00:02.0 VGA compatible controller: Intel Corporation 4 Series Chipset Integrated Graphics Controller (rev 03)

    (The motherboard is Intel G41 Chipset)

     

    $ lsmod | grep i915

    i915                  614894  3
    i2c_algo_bit           13257  1 i915
    drm_kms_helper         50210  1 i915
    drm                   272504  4 i915,drm_kms_helper
    i2c_core               34242  5 drm,i915,i2c_i801,drm_kms_helper,i2c_algo_bit
    video                  19052  1 i915

    It would be great if anyone can help me out with this. Please let me know if more information from configuration/logs is required.

    Thanks in advance

    Regards

    Vaibhav

     

     

    Aug 31, 2013 - 11:18pm
  • Hi Vaibhav,

     

    What about before the installer, did you have a chance to check what resolution you could achieve?

    What does xrandr --verbose reports?

    Could you please boot with drm.debug=0xe and paste your dmesg.log here? Also, all Xorg logs probably under /var/logs are useful as well.

    Thanks,

    Rodrigo

    Sep 03, 2013 - 12:26pm
  • TD P { margin-bottom: 0in; }P { margin-bottom: 0.08in; }

    Hi Rodrigo

    Thanks for your support.

    • What about before the installer, did you have a chance to check what resolution you could achieve? The highset resolution I could get prior and post installer is same 1024X768

    • Please find output of log files after booting with parameter drm.debug=0xe

    • Please let me know in case you need more information from my side

    # xrandr --verbose

    # dmesg

    # cat /var/log/Xorg.0.log

    Screen 0: minimum 320 x 200, current 1024 x 768, maximum 8192 x 8192

    VGA1 connected primary 1024x768+0+0 (0x45) normal (normal left inverted right x axis y axis) 0mm x 0mm

    Identifier: 0x41

    Timestamp: 30861

    Subpixel: unknown

    Gamma: 1.0:1.0:1.0

    Brightness: 1.0

    Clones:

    CRTC: 0

    CRTCs: 0 1

    Transform: 1.000000 0.000000 0.000000

    0.000000 1.000000 0.000000

    0.000000 0.000000 1.000000

    filter:

    1024x768 (0x45) 65.0MHz -HSync -VSync *current

    h: width 1024 start 1048 end 1184 total 1344 skew 0 clock 48.4KHz

    v: height 768 start 771 end 777 total 806 clock 60.0Hz

    800x600 (0x46) 40.0MHz +HSync +VSync

    h: width 800 start 840 end 968 total 1056 skew 0 clock 37.9KHz

    v: height 600 start 601 end 605 total 628 clock 60.3Hz

    800x600 (0x47) 36.0MHz +HSync +VSync

    h: width 800 start 824 end 896 total 1024 skew 0 clock 35.2KHz

    v: height 600 start 601 end 603 total 625 clock 56.2Hz

    848x480 (0x48) 33.8MHz +HSync +VSync

    h: width 848 start 864 end 976 total 1088 skew 0 clock 31.0KHz

    v: height 480 start 486 end 494 total 517 clock 60.0Hz

    640x480 (0x49) 25.2MHz -HSync -VSync

    h: width 640 start 656 end 752 total 800 skew 0 clock 31.5KHz

    v: height 480 start 489 end 492 total 525 clock 59.9Hz

    HDMI1 disconnected (normal left inverted right x axis y axis)

    Identifier: 0x42

    Timestamp: 30861

    Subpixel: unknown

    Clones:

    CRTCs: 0 1

    Transform: 1.000000 0.000000 0.000000

    0.000000 1.000000 0.000000

    0.000000 0.000000 1.000000

    filter:

    Broadcast RGB: Automatic

    supported: AutomaticFullLimited 16:235

    audio: auto

    supported: force-dvioffautoon

    DP1 disconnected (normal left inverted right x axis y axis)

    Identifier: 0x43

    Timestamp: 30861

    Subpixel: unknown

    Clones:

    CRTCs: 0 1

    Transform: 1.000000 0.000000 0.000000

    0.000000 1.000000 0.000000

    0.000000 0.000000 1.000000

    filter:

    Broadcast RGB: Automatic

    supported: AutomaticFullLimited 16:235

    audio: auto

    supported: force-dvioffautoon

    [ 0.000000] Initializing cgroup subsys cpuset

    [ 0.000000] Initializing cgroup subsys cpu

    [ 0.000000] Initializing cgroup subsys cpuacct

    [ 0.000000] Linux version 3.10.10-200.fc19.x86_64 (mockbuild@bkernel01.phx2.fedoraproject.org) (gcc version 4.8.1 20130603 (Red Hat 4.8.1-1) (GCC) ) #1 SMP Thu Aug 29 19:05:45 UTC 2013

    [ 0.000000] Command line: BOOT_IMAGE=/vmlinuz-3.10.10-200.fc19.x86_64 root=/dev/mapper/fedora-root ro rd.lvm.lv=fedora/swap rd.md=0 rd.dm=0 vconsole.keymap=us rd.luks=0 vconsole.font=latarcyrheb-sun16 rd.lvm.lv=fedora/root rhgb quiet LANG=en_US.UTF-8

    [ 0.000000] e820: BIOS-provided physical RAM map:

    [ 0.000000] BIOS-e820: [mem 0x0000000000000000-0x000000000009fbff] usable

    [ 0.000000] BIOS-e820: [mem 0x000000000009fc00-0x000000000009ffff] reserved

    [ 0.000000] BIOS-e820: [mem 0x00000000000e0000-0x00000000000fffff] reserved

    [ 0.000000] BIOS-e820: [mem 0x0000000000100000-0x000000007d8c5fff] usable

    [ 0.000000] BIOS-e820: [mem 0x000000007d8c6000-0x000000007d907fff] ACPI NVS

    [ 0.000000] BIOS-e820: [mem 0x000000007d908000-0x000000007da44fff] reserved

    [ 0.000000] BIOS-e820: [mem 0x000000007da45000-0x000000007da58fff] ACPI NVS

    [ 0.000000] BIOS-e820: [mem 0x000000007da59000-0x000000007db56fff] reserved

    [ 0.000000] BIOS-e820: [mem 0x000000007db57000-0x000000007db57fff] ACPI NVS

    [ 0.000000] BIOS-e820: [mem 0x000000007db58000-0x000000007db60fff] ACPI data

    [ 0.000000] BIOS-e820: [mem 0x000000007db61000-0x000000007db6afff] ACPI NVS

    [ 0.000000] BIOS-e820: [mem 0x000000007db6b000-0x000000007db89fff] reserved

    [ 0.000000] BIOS-e820: [mem 0x000000007db8a000-0x000000007db8ffff] ACPI NVS

    [ 0.000000] BIOS-e820: [mem 0x000000007db90000-0x000000007dcfffff] usable

    [ 0.000000] BIOS-e820: [mem 0x00000000fec00000-0x00000000fec00fff] reserved

    [ 0.000000] BIOS-e820: [mem 0x00000000fed00000-0x00000000fed00fff] reserved

    [ 0.000000] BIOS-e820: [mem 0x00000000fed1c000-0x00000000fed8ffff] reserved

    [ 0.000000] BIOS-e820: [mem 0x00000000fff00000-0x00000000ffffffff] reserved

    [ 0.000000] NX (Execute Disable) protection: active

    [ 0.000000] SMBIOS 2.4 present.

    [ 0.000000] DMI: /DG41TY, BIOS TYG4110H.86A.0018.2008.1117.1920 11/17/2008

    [ 0.000000] e820: update [mem 0x00000000-0x00000fff] usable ==> reserved

    [ 0.000000] e820: remove [mem 0x000a0000-0x000fffff] usable

    [ 0.000000] No AGP bridge found

    [ 0.000000] e820: last_pfn = 0x7dd00 max_arch_pfn = 0x400000000

    [ 0.000000] MTRR default type: uncachable

    [ 0.000000] MTRR fixed ranges enabled:

    [ 0.000000] 00000-9FFFF write-back

    [ 0.000000] A0000-E7FFF uncachable

    [ 0.000000] E8000-FFFFF write-protect

    [ 0.000000] MTRR variable ranges enabled:

    [ 0.000000] 0 base 000000000 mask F80000000 write-back

    [ 0.000000] 1 base 07DD00000 mask FFFF00000 write-through

    [ 0.000000] 2 base 07DE00000 mask FFFE00000 uncachable

    [ 0.000000] 3 base 07E000000 mask FFE000000 uncachable

    [ 0.000000] 4 disabled

    [ 0.000000] 5 disabled

    [ 0.000000] 6 disabled

    [ 0.000000] x86 PAT enabled: cpu 0, old 0x7040600070406, new 0x7010600070106

    [ 0.000000] found SMP MP-table at [mem 0x000fd460-0x000fd46f] mapped at [ffff8800000fd460]

    [ 0.000000] Base memory trampoline at [ffff880000099000] 99000 size 24576

    [ 0.000000] init_memory_mapping: [mem 0x00000000-0x000fffff]

    [ 0.000000] [mem 0x00000000-0x000fffff] page 4k

    [ 0.000000] BRK [0x01fde000, 0x01fdefff] PGTABLE

    [ 0.000000] BRK [0x01fdf000, 0x01fdffff] PGTABLE

    [ 0.000000] BRK [0x01fe0000, 0x01fe0fff] PGTABLE

    [ 0.000000] init_memory_mapping: [mem 0x7d600000-0x7d7fffff]

    [ 0.000000] [mem 0x7d600000-0x7d7fffff] page 2M

    [ 0.000000] BRK [0x01fe1000, 0x01fe1fff] PGTABLE

    [ 0.000000] init_memory_mapping: [mem 0x7c000000-0x7d5fffff]

    [ 0.000000] [mem 0x7c000000-0x7d5fffff] page 2M

    [ 0.000000] init_memory_mapping: [mem 0x00100000-0x7bffffff]

    [ 0.000000] [mem 0x00100000-0x001fffff] page 4k

    [ 0.000000] [mem 0x00200000-0x7bffffff] page 2M

    [ 0.000000] init_memory_mapping: [mem 0x7d800000-0x7d8c5fff]

    [ 0.000000] [mem 0x7d800000-0x7d8c5fff] page 4k

    [ 0.000000] BRK [0x01fe2000, 0x01fe2fff] PGTABLE

    [ 0.000000] init_memory_mapping: [mem 0x7db90000-0x7dcfffff]

    [ 0.000000] [mem 0x7db90000-0x7dcfffff] page 4k

    [ 0.000000] RAMDISK: [mem 0x36e58000-0x37723fff]

    [ 0.000000] ACPI: RSDP 00000000000f03c0 00024 (v02 INTEL)

    [ 0.000000] ACPI: XSDT 000000007db5fe18 00044 (v01 INTEL DG41TY 00000012 MSFT 00010013)

    [ 0.000000] ACPI: FACP 000000007db5ed98 000F4 (v04 INTEL DG41TY 00000012 MSFT 00010013)

    [ 0.000000] ACPI Warning: 32/64 FACS address mismatch in FADT - two FACS tables! (20130328/tbfadt-395)

    [ 0.000000] ACPI BIOS Bug: Warning: 32/64X FACS address mismatch in FADT - 0x7DB62F40/0x000000007DB67F40, using 32 (20130328/tbfadt-522)

    [ 0.000000] ACPI: DSDT 000000007db58018 05B02 (v01 INTEL DG41TY 00000008 INTL 20051117)

    [ 0.000000] ACPI: FACS 000000007db62f40 00040

    [ 0.000000] ACPI: APIC 000000007db5ef18 0006C (v02 INTEL DG41TY 00000012 MSFT 00010013)

    [ 0.000000] ACPI: MCFG 000000007db69e18 0003C (v01 INTEL DG41TY 00000012 MSFT 00000097)

    [ 0.000000] ACPI: HPET 000000007db69d98 00038 (v01 INTEL DG41TY 00000012 AMI. 00000003)

    [ 0.000000] ACPI: Local APIC address 0xfee00000

    [ 0.000000] No NUMA configuration found

    [ 0.000000] Faking a node at [mem 0x0000000000000000-0x000000007dcfffff]

    [ 0.000000] Initmem setup node 0 [mem 0x00000000-0x7dcfffff]

    [ 0.000000] NODE_DATA [mem 0x7dcec000-0x7dcfffff]

    [ 0.000000] [ffffea0000000000-ffffea0001ffffff] PMD -> [ffff88007b000000-ffff88007cffffff] on node 0

    [ 0.000000] Zone ranges:

    [ 0.000000] DMA [mem 0x00001000-0x00ffffff]

    [ 0.000000] DMA32 [mem 0x01000000-0xffffffff]

    [ 0.000000] Normal empty

    [ 0.000000] Movable zone start for each node

    [ 0.000000] Early memory node ranges

    [ 0.000000] node 0: [mem 0x00001000-0x0009efff]

    [ 0.000000] node 0: [mem 0x00100000-0x7d8c5fff]

    [ 0.000000] node 0: [mem 0x7db90000-0x7dcfffff]

    [ 0.000000] On node 0 totalpages: 514516

    [ 0.000000] DMA zone: 64 pages used for memmap

    [ 0.000000] DMA zone: 21 pages reserved

    [ 0.000000] DMA zone: 3998 pages, LIFO batch:0

    [ 0.000000] DMA32 zone: 7988 pages used for memmap

    [ 0.000000] DMA32 zone: 510518 pages, LIFO batch:31

    [ 0.000000] ACPI: PM-Timer IO Port: 0x808

    [ 0.000000] ACPI: Local APIC address 0xfee00000

    [ 0.000000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)

    [ 0.000000] ACPI: LAPIC (acpi_id[0x02] lapic_id[0x01] enabled)

    [ 0.000000] ACPI: LAPIC (acpi_id[0x03] lapic_id[0x02] disabled)

    [ 0.000000] ACPI: LAPIC (acpi_id[0x04] lapic_id[0x03] disabled)

    [ 0.000000] ACPI: IOAPIC (id[0x04] address[0xfec00000] gsi_base[0])

    [ 0.000000] IOAPIC[0]: apic_id 4, version 32, address 0xfec00000, GSI 0-23

    [ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)

    [ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)

    [ 0.000000] ACPI: IRQ0 used by override.

    [ 0.000000] ACPI: IRQ2 used by override.

    [ 0.000000] ACPI: IRQ9 used by override.

    [ 0.000000] Using ACPI (MADT) for SMP configuration information

    [ 0.000000] ACPI: HPET id: 0x8086a201 base: 0xfed00000

    [ 0.000000] smpboot: Allowing 4 CPUs, 2 hotplug CPUs

    [ 0.000000] nr_irqs_gsi: 40

    [ 0.000000] PM: Registered nosave memory: 000000000009f000 - 00000000000a0000

    [ 0.000000] PM: Registered nosave memory: 00000000000a0000 - 00000000000e0000

    [ 0.000000] PM: Registered nosave memory: 00000000000e0000 - 0000000000100000

    [ 0.000000] PM: Registered nosave memory: 000000007d8c6000 - 000000007d908000

    [ 0.000000] PM: Registered nosave memory: 000000007d908000 - 000000007da45000

    [ 0.000000] PM: Registered nosave memory: 000000007da45000 - 000000007da59000

    [ 0.000000] PM: Registered nosave memory: 000000007da59000 - 000000007db57000

    [ 0.000000] PM: Registered nosave memory: 000000007db57000 - 000000007db58000

    [ 0.000000] PM: Registered nosave memory: 000000007db58000 - 000000007db61000

    [ 0.000000] PM: Registered nosave memory: 000000007db61000 - 000000007db6b000

    [ 0.000000] PM: Registered nosave memory: 000000007db6b000 - 000000007db8a000

    [ 0.000000] PM: Registered nosave memory: 000000007db8a000 - 000000007db90000

    [ 0.000000] e820: [mem 0x7dd00000-0xfebfffff] available for PCI devices

    [ 0.000000] Booting paravirtualized kernel on bare hardware

    [ 0.000000] setup_percpu: NR_CPUS:128 nr_cpumask_bits:128 nr_cpu_ids:4 nr_node_ids:1

    [ 0.000000] PERCPU: Embedded 28 pages/cpu @ffff88007d600000 s85440 r8192 d21056 u524288

    [ 0.000000] pcpu-alloc: s85440 r8192 d21056 u524288 alloc=1*2097152

    [ 0.000000] pcpu-alloc: [0] 0 1 2 3

    [ 0.000000] Built 1 zonelists in Node order, mobility grouping on. Total pages: 506443

    [ 0.000000] Policy zone: DMA32

    [ 0.000000] Kernel command line: BOOT_IMAGE=/vmlinuz-3.10.10-200.fc19.x86_64 root=/dev/mapper/fedora-root ro rd.lvm.lv=fedora/swap rd.md=0 rd.dm=0 vconsole.keymap=us rd.luks=0 vconsole.font=latarcyrheb-sun16 rd.lvm.lv=fedora/root rhgb quiet LANG=en_US.UTF-8

    [ 0.000000] PID hash table entries: 4096 (order: 3, 32768 bytes)

    [ 0.000000] xsave: enabled xstate_bv 0x3, cntxt size 0x240

    [ 0.000000] Checking aperture...

    [ 0.000000] No AGP bridge found

    [ 0.000000] Memory: 1999292k/2061312k available (6447k kernel code, 3248k absent, 58772k reserved, 6813k data, 1412k init)

    [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1

    [ 0.000000] Hierarchical RCU implementation.

    [ 0.000000] RCU restricting CPUs from NR_CPUS=128 to nr_cpu_ids=4.

    [ 0.000000] NR_IRQS:8448 nr_irqs:712 16

    [ 0.000000] spurious 8259A interrupt: IRQ7.

    [ 0.000000] Console: colour VGA+ 80x25

    [ 0.000000] console [tty0] enabled

    [ 0.000000] allocated 8388608 bytes of page_cgroup

    [ 0.000000] please try 'cgroup_disable=memory' option if you don't want memory cgroups

    [ 0.000000] hpet clockevent registered

    [ 0.000000] tsc: Fast TSC calibration using PIT

    [ 0.000000] tsc: Detected 2800.154 MHz processor

    [ 0.001004] Calibrating delay loop (skipped), value calculated using timer frequency.. 5600.30 BogoMIPS (lpj=2800154)

    [ 0.001007] pid_max: default: 32768 minimum: 301

    [ 0.001041] Security Framework initialized

    [ 0.001054] SELinux: Initializing.

    [ 0.001062] SELinux: Starting in permissive mode

    [ 0.001259] Dentry cache hash table entries: 262144 (order: 9, 2097152 bytes)

    [ 0.002767] Inode-cache hash table entries: 131072 (order: 8, 1048576 bytes)

    [ 0.003296] Mount-cache hash table entries: 256

    [ 0.003528] Initializing cgroup subsys memory

    [ 0.003545] Initializing cgroup subsys devices

    [ 0.003547] Initializing cgroup subsys freezer

    [ 0.003549] Initializing cgroup subsys net_cls

    [ 0.003551] Initializing cgroup subsys blkio

    [ 0.003553] Initializing cgroup subsys perf_event

    [ 0.003586] CPU: Physical Processor ID: 0

    [ 0.003587] CPU: Processor Core ID: 0

    [ 0.003589] mce: CPU supports 6 MCE banks

    [ 0.003596] CPU0: Thermal monitoring enabled (TM2)

    [ 0.003604] Last level iTLB entries: 4KB 128, 2MB 4, 4MB 4

    Last level dTLB entries: 4KB 256, 2MB 0, 4MB 32

    tlb_flushall_shift: -1

    [ 0.003677] Freeing SMP alternatives: 24k freed

    [ 0.005021] ACPI: Core revision 20130328

    [ 0.006833] ACPI: All ACPI Tables successfully acquired

    [ 0.006955] ftrace: allocating 24748 entries in 97 pages

    [ 0.013418] ..TIMER: vector=0x30 apic1=0 pin1=2 apic2=0 pin2=0

    [ 0.023427] smpboot: CPU0: Intel(R) Core(TM)2 Duo CPU E7400 @ 2.80GHz (fam: 06, model: 17, stepping: 0a)

    [ 0.024000] Performance Events: PEBS fmt0+, 4-deep LBR, Core2 events, Intel PMU driver.

    [ 0.024000] ... version: 2

    [ 0.024000] ... bit width: 40

    [ 0.024000] ... generic registers: 2

    [ 0.024000] ... value mask: 000000ffffffffff

    [ 0.024000] ... max period: 000000007fffffff

    [ 0.024000] ... fixed-purpose events: 3

    [ 0.024000] ... event mask: 0000000700000003

    [ 0.024474] smpboot: Booting Node 0, Processors #1

    [ 0.036042] Brought up 2 CPUs

    [ 0.036048] smpboot: Total of 2 processors activated (11200.61 BogoMIPS)

    [ 0.036155] NMI watchdog: enabled on all CPUs, permanently consumes one hw-PMU counter.

    [ 0.037127] devtmpfs: initialized

    [ 0.037145] PM: Registering ACPI NVS region [mem 0x7d8c6000-0x7d907fff] (270336 bytes)

    [ 0.037145] PM: Registering ACPI NVS region [mem 0x7da45000-0x7da58fff] (81920 bytes)

    [ 0.037145] PM: Registering ACPI NVS region [mem 0x7db57000-0x7db57fff] (4096 bytes)

    [ 0.037145] PM: Registering ACPI NVS region [mem 0x7db61000-0x7db6afff] (40960 bytes)

    [ 0.037145] PM: Registering ACPI NVS region [mem 0x7db8a000-0x7db8ffff] (24576 bytes)

    [ 0.037935] atomic64 test passed for x86-64 platform with CX8 and with SSE

    [ 0.037958] RTC time: 1:53:46, date: 09/04/13

    [ 0.038053] NET: Registered protocol family 16

    [ 0.038216] ACPI: bus type PCI registered

    [ 0.038218] acpiphp: ACPI Hot Plug PCI Controller Driver version: 0.5

    [ 0.038275] PCI: MMCONFIG for domain 0000 [bus 00-ff] at [mem 0xe0000000-0xefffffff] (base 0xe0000000)

    [ 0.038277] PCI: not using MMCONFIG

    [ 0.038278] PCI: Using configuration type 1 for base access

    [ 0.039049] bio: create slab <bio-0> at 0

    [ 0.039049] ACPI: Added _OSI(Module Device)

    [ 0.039049] ACPI: Added _OSI(Processor Device)

    [ 0.039049] ACPI: Added _OSI(3.0 _SCP Extensions)

    [ 0.039049] ACPI: Added _OSI(Processor Aggregator Device)

    [ 0.039687] ACPI: EC: Look up EC in DSDT

    [ 0.040632] ACPI: Executed 1 blocks of module-level executable AML code

    [ 0.042145] ACPI: SSDT 000000007db62c18 002CC (v01 AMI IST 00000001 MSFT 03000001)

    [ 0.042351] ACPI: Dynamic OEM Table Load:

    [ 0.042353] ACPI: SSDT (null) 002CC (v01 AMI IST 00000001 MSFT 03000001)

    [ 0.042535] ACPI: Interpreter enabled

    [ 0.042541] ACPI Exception: AE_NOT_FOUND, While evaluating Sleep State [\_S1_] (20130328/hwxface-568)

    [ 0.042544] ACPI Exception: AE_NOT_FOUND, While evaluating Sleep State [\_S2_] (20130328/hwxface-568)

    [ 0.042556] ACPI: (supports S0 S3 S4 S5)

    [ 0.042557] ACPI: Using IOAPIC for interrupt routing

    [ 0.042578] PCI: MMCONFIG for domain 0000 [bus 00-ff] at [mem 0xe0000000-0xefffffff] (base 0xe0000000)

    [ 0.042608] PCI: MMCONFIG at [mem 0xe0000000-0xefffffff] reserved in ACPI motherboard resources

    [ 0.062587] PCI: Using host bridge windows from ACPI; if necessary, use "pci=nocrs" and report a bug

    [ 0.062640] ACPI: No dock devices found.

    [ 0.062874] [Firmware Bug]: ACPI: BIOS _OSI(Linux) query ignored

    [ 0.067303] ACPI: PCI Root Bridge [PCI0] (domain 0000 [bus 00-ff])

    [ 0.067497] PCI host bridge to bus 0000:00

    [ 0.067500] pci_bus 0000:00: root bus resource [bus 00-ff]

    [ 0.067502] pci_bus 0000:00: root bus resource [io 0x0000-0x0cf7]

    [ 0.067504] pci_bus 0000:00: root bus resource [io 0x0d00-0xffff]

    [ 0.067506] pci_bus 0000:00: root bus resource [mem 0x000a0000-0x000bffff]

    [ 0.067507] pci_bus 0000:00: root bus resource [mem 0x80000000-0xffffffff]

    [ 0.067515] pci 0000:00:00.0: [8086:2e30] type 00 class 0x060000

    [ 0.067533] DMAR: Forcing write-buffer flush capability

    [ 0.067534] DMAR: Disabling IOMMU for graphics on this chipset

    [ 0.067593] pci 0000:00:02.0: [8086:2e32] type 00 class 0x030000

    [ 0.067603] pci 0000:00:02.0: reg 10: [mem 0xd0000000-0xd03fffff 64bit]

    [ 0.067609] pci 0000:00:02.0: reg 18: [mem 0xc0000000-0xcfffffff 64bit pref]

    [ 0.067613] pci 0000:00:02.0: reg 20: [io 0xf140-0xf147]

    [ 0.067704] pci 0000:00:1b.0: [8086:27d8] type 00 class 0x040300

    [ 0.067717] pci 0000:00:1b.0: reg 10: [mem 0xd0500000-0xd0503fff 64bit]

    [ 0.067775] pci 0000:00:1b.0: PME# supported from D0 D3hot D3cold

    [ 0.067836] pci 0000:00:1c.0: [8086:27d0] type 01 class 0x060400

    [ 0.067894] pci 0000:00:1c.0: PME# supported from D0 D3hot D3cold

    [ 0.067931] pci 0000:00:1c.0: System wakeup disabled by ACPI

    [ 0.067961] pci 0000:00:1c.1: [8086:27d2] type 01 class 0x060400

    [ 0.068020] pci 0000:00:1c.1: PME# supported from D0 D3hot D3cold

    [ 0.068056] pci 0000:00:1c.1: System wakeup disabled by ACPI

    [ 0.068088] pci 0000:00:1d.0: [8086:27c8] type 00 class 0x0c0300

    [ 0.068122] pci 0000:00:1d.0: reg 20: [io 0xf080-0xf09f]

    [ 0.068178] pci 0000:00:1d.0: System wakeup disabled by ACPI

    [ 0.068207] pci 0000:00:1d.1: [8086:27c9] type 00 class 0x0c0300

    [ 0.068241] pci 0000:00:1d.1: reg 20: [io 0xf060-0xf07f]

    [ 0.068300] pci 0000:00:1d.1: System wakeup disabled by ACPI

    [ 0.068330] pci 0000:00:1d.2: [8086:27ca] type 00 class 0x0c0300

    [ 0.068364] pci 0000:00:1d.2: reg 20: [io 0xf040-0xf05f]

    [ 0.068421] pci 0000:00:1d.2: System wakeup disabled by ACPI

    [ 0.068449] pci 0000:00:1d.3: [8086:27cb] type 00 class 0x0c0300

    [ 0.068483] pci 0000:00:1d.3: reg 20: [io 0xf020-0xf03f]

    [ 0.068538] pci 0000:00:1d.3: System wakeup disabled by ACPI

    [ 0.068574] pci 0000:00:1d.7: [8086:27cc] type 00 class 0x0c0320

    [ 0.068591] pci 0000:00:1d.7: reg 10: [mem 0xd0504000-0xd05043ff]

    [ 0.068662] pci 0000:00:1d.7: PME# supported from D0 D3hot D3cold

    [ 0.068695] pci 0000:00:1d.7: System wakeup disabled by ACPI

    [ 0.068724] pci 0000:00:1e.0: [8086:244e] type 01 class 0x060401

    [ 0.068792] pci 0000:00:1e.0: System wakeup disabled by ACPI

    [ 0.068823] pci 0000:00:1f.0: [8086:27b8] type 00 class 0x060100

    [ 0.068892] pci 0000:00:1f.0: quirk: [io 0x0800-0x087f] claimed by ICH6 ACPI/GPIO/TCO

    [ 0.068897] pci 0000:00:1f.0: quirk: [io 0x0480-0x04bf] claimed by ICH6 GPIO

    [ 0.068900] pci 0000:00:1f.0: ICH7 LPC Generic IO decode 1 PIO at 0a00 (mask 00ff)

    [ 0.068978] pci 0000:00:1f.1: [8086:27df] type 00 class 0x01018a

    [ 0.068989] pci 0000:00:1f.1: reg 10: [io 0x0000-0x0007]

    [ 0.068997] pci 0000:00:1f.1: reg 14: [io 0x0000-0x0003]

    [ 0.069007] pci 0000:00:1f.1: reg 18: [io 0x08f0-0x08f7]

    [ 0.069015] pci 0000:00:1f.1: reg 1c: [io 0x08f8-0x08fb]

    [ 0.069023] pci 0000:00:1f.1: reg 20: [io 0xf0f0-0xf0ff]

    [ 0.069092] pci 0000:00:1f.2: [8086:27c0] type 00 class 0x01018f

    [ 0.069104] pci 0000:00:1f.2: reg 10: [io 0xf0e0-0xf0e7]

    [ 0.069111] pci 0000:00:1f.2: reg 14: [io 0xf0d0-0xf0d3]

    [ 0.069118] pci 0000:00:1f.2: reg 18: [io 0xf0c0-0xf0c7]

    [ 0.069124] pci 0000:00:1f.2: reg 1c: [io 0xf0b0-0xf0b3]

    [ 0.069131] pci 0000:00:1f.2: reg 20: [io 0xf0a0-0xf0af]

    [ 0.069161] pci 0000:00:1f.2: PME# supported from D3hot

    [ 0.069217] pci 0000:00:1f.3: [8086:27da] type 00 class 0x0c0500

    [ 0.069262] pci 0000:00:1f.3: reg 20: [io 0x0400-0x041f]

    [ 0.069374] pci 0000:00:1c.0: PCI bridge to [bus 01]

    [ 0.069442] pci 0000:02:00.0: [10ec:8168] type 00 class 0x020000

    [ 0.069457] pci 0000:02:00.0: reg 10: [io 0xe000-0xe0ff]

    [ 0.069483] pci 0000:02:00.0: reg 18: [mem 0xd0414000-0xd0414fff 64bit pref]

    [ 0.069499] pci 0000:02:00.0: reg 20: [mem 0xd0410000-0xd0413fff 64bit pref]

    [ 0.069510] pci 0000:02:00.0: reg 30: [mem 0xd0400000-0xd040ffff pref]

    [ 0.069569] pci 0000:02:00.0: supports D1 D2

    [ 0.069571] pci 0000:02:00.0: PME# supported from D0 D1 D2 D3hot D3cold

    [ 0.072019] pci 0000:00:1c.1: PCI bridge to [bus 02]

    [ 0.072025] pci 0000:00:1c.1: bridge window [io 0xe000-0xefff]

    [ 0.072030] pci 0000:00:1c.1: bridge window [mem 0xd0400000-0xd04fffff]

    [ 0.072119] pci 0000:00:1e.0: PCI bridge to [bus 03] (subtractive decode)

    [ 0.072130] pci 0000:00:1e.0: bridge window [io 0x0000-0x0cf7] (subtractive decode)

    [ 0.072133] pci 0000:00:1e.0: bridge window [io 0x0d00-0xffff] (subtractive decode)

    [ 0.072136] pci 0000:00:1e.0: bridge window [mem 0x000a0000-0x000bffff] (subtractive decode)

    [ 0.072139] pci 0000:00:1e.0: bridge window [mem 0x80000000-0xffffffff] (subtractive decode)

    [ 0.072242] acpi PNP0A08:00: Requesting ACPI _OSC control (0x1d)

    [ 0.072354] acpi PNP0A08:00: ACPI _OSC control (0x1d) granted

    [ 0.072798] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 *10 12 14 15)

    [ 0.072844] ACPI: PCI Interrupt Link [LNKB] (IRQs *3 4 5 6 7 10 11 12 14 15)

    [ 0.072890] ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 6 7 *10 11 12 14 15)

    [ 0.072934] ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 10 *11 12 14 15)

    [ 0.072982] ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled.

    [ 0.073035] ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled.

    [ 0.073081] ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled.

    [ 0.073126] ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 6 *7 10 11 12 14 15)

    [ 0.073198] ACPI: Enabled 2 GPEs in block 00 to 1F

    [ 0.073203] acpi root: \_SB_.PCI0 notify handler is installed

    [ 0.073227] Found 1 acpi root devices

    [ 0.073279] vgaarb: device added: PCI:0000:00:02.0,decodes=io+mem,owns=io+mem,locks=none

    [ 0.073279] vgaarb: loaded

    [ 0.073279] vgaarb: bridge control possible 0000:00:02.0

    [ 0.074032] SCSI subsystem initialized

    [ 0.074034] ACPI: bus type ATA registered

    [ 0.074050] libata version 3.00 loaded.

    [ 0.074050] ACPI: bus type USB registered

    [ 0.074050] usbcore: registered new interface driver usbfs

    [ 0.074058] usbcore: registered new interface driver hub

    [ 0.074061] usbcore: registered new device driver usb

    [ 0.074061] PCI: Using ACPI for IRQ routing

    [ 0.079312] PCI: pci_cache_line_size set to 64 bytes

    [ 0.079347] e820: reserve RAM buffer [mem 0x0009fc00-0x0009ffff]

    [ 0.079349] e820: reserve RAM buffer [mem 0x7d8c6000-0x7fffffff]

    [ 0.079351] e820: reserve RAM buffer [mem 0x7dd00000-0x7fffffff]

    [ 0.079434] NetLabel: Initializing

    [ 0.079436] NetLabel: domain hash size = 128

    [ 0.079437] NetLabel: protocols = UNLABELED CIPSOv4

    [ 0.079449] NetLabel: unlabeled traffic allowed by default

    [ 0.079494] HPET: 3 timers in total, 0 timers will be used for per-cpu timer

    [ 0.079497] hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0

    [ 0.079501] hpet0: 3 comparators, 64-bit 14.318180 MHz counter

    [ 0.081009] Switching to clocksource hpet

    [ 0.086780] pnp: PnP ACPI init

    [ 0.086803] ACPI: bus type PNP registered

    [ 0.086924] system 00:00: [mem 0xfed14000-0xfed19fff] has been reserved

    [ 0.086926] system 00:00: [mem 0xe0000000-0xefffffff] has been reserved

    [ 0.086931] system 00:00: Plug and Play ACPI device, IDs PNP0c01 (active)

    [ 0.087071] system 00:01: [io 0x0800-0x087f] has been reserved

    [ 0.087074] system 00:01: [io 0x0480-0x04bf] has been reserved

    [ 0.087076] system 00:01: [mem 0xfec00000-0xfec00fff] could not be reserved

    [ 0.087079] system 00:01: [mem 0xfee00000-0xfee00fff] has been reserved

    [ 0.087081] system 00:01: [mem 0xfed1c000-0xfed1ffff] has been reserved

    [ 0.087083] system 00:01: [mem 0xfed20000-0xfed8ffff] has been reserved

    [ 0.087085] system 00:01: [mem 0xff000000-0xffffffff] could not be reserved

    [ 0.087088] system 00:01: Plug and Play ACPI device, IDs PNP0c02 (active)

    [ 0.087206] system 00:02: Plug and Play ACPI device, IDs PNP0c02 (active)

    [ 0.087259] pnp 00:03: Plug and Play ACPI device, IDs PNP0303 PNP030b (active)

    [ 0.087463] pnp 00:04: [dma 2]

    [ 0.087504] pnp 00:04: Plug and Play ACPI device, IDs PNP0700 (active)

    [ 0.087666] pnp 00:05: [dma 0 disabled]

    [ 0.087713] pnp 00:05: Plug and Play ACPI device, IDs PNP0501 (active)

    [ 0.087949] pnp 00:06: [dma 3]

    [ 0.088064] pnp 00:06: Plug and Play ACPI device, IDs PNP0401 (active)

    [ 0.088074] pnp 00:07: [dma 4]

    [ 0.088090] pnp 00:07: Plug and Play ACPI device, IDs PNP0200 (active)

    [ 0.088140] pnp 00:08: Plug and Play ACPI device, IDs PNP0b00 (active)

    [ 0.088161] pnp 00:09: Plug and Play ACPI device, IDs PNP0800 (active)

    [ 0.088206] system 00:0a: [io 0x04d0-0x04d1] has been reserved

    [ 0.088209] system 00:0a: Plug and Play ACPI device, IDs PNP0c02 (active)

    [ 0.088237] pnp 00:0b: Plug and Play ACPI device, IDs PNP0c04 (active)

    [ 0.088349] pnp 00:0c: Plug and Play ACPI device, IDs PNP0103 (active)

    [ 0.088453] pnp: PnP ACPI: found 13 devices

    [ 0.088455] ACPI: bus type PNP unregistered

    [ 0.094805] pci 0000:00:1c.0: bridge window [io 0x1000-0x0fff] to [bus 01] add_size 1000

    [ 0.094809] pci 0000:00:1c.0: bridge window [mem 0x00100000-0x000fffff 64bit pref] to [bus 01] add_size 200000

    [ 0.094812] pci 0000:00:1c.0: bridge window [mem 0x00100000-0x000fffff] to [bus 01] add_size 200000

    [ 0.094819] pci 0000:00:1c.1: bridge window [mem 0x00100000-0x000fffff 64bit pref] to [bus 02] add_size 200000

    [ 0.094829] pci 0000:00:1c.0: res[14]=[mem 0x00100000-0x000fffff] get_res_add_size add_size 200000

    [ 0.094831] pci 0000:00:1c.0: res[15]=[mem 0x00100000-0x000fffff 64bit pref] get_res_add_size add_size 200000

    [ 0.094833] pci 0000:00:1c.1: res[15]=[mem 0x00100000-0x000fffff 64bit pref] get_res_add_size add_size 200000

    [ 0.094835] pci 0000:00:1c.0: res[13]=[io 0x1000-0x0fff] get_res_add_size add_size 1000

    [ 0.094839] pci 0000:00:1c.0: BAR 14: assigned [mem 0x80000000-0x801fffff]

    [ 0.094842] pci 0000:00:1c.0: BAR 15: assigned [mem 0x80200000-0x803fffff 64bit pref]

    [ 0.094844] pci 0000:00:1c.1: BAR 15: assigned [mem 0x80400000-0x805fffff 64bit pref]

    [ 0.094847] pci 0000:00:1c.0: BAR 13: assigned [io 0x1000-0x1fff]

    [ 0.094849] pci 0000:00:1c.0: PCI bridge to [bus 01]

    [ 0.094852] pci 0000:00:1c.0: bridge window [io 0x1000-0x1fff]

    [ 0.094856] pci 0000:00:1c.0: bridge window [mem 0x80000000-0x801fffff]

    [ 0.094859] pci 0000:00:1c.0: bridge window [mem 0x80200000-0x803fffff 64bit pref]

    [ 0.094864] pci 0000:00:1c.1: PCI bridge to [bus 02]

    [ 0.094867] pci 0000:00:1c.1: bridge window [io 0xe000-0xefff]

    [ 0.094871] pci 0000:00:1c.1: bridge window [mem 0xd0400000-0xd04fffff]

    [ 0.094874] pci 0000:00:1c.1: bridge window [mem 0x80400000-0x805fffff 64bit pref]

    [ 0.094879] pci 0000:00:1e.0: PCI bridge to [bus 03]

    [ 0.094979] pci 0000:00:1e.0: setting latency timer to 64

    [ 0.094983] pci_bus 0000:00: resource 4 [io 0x0000-0x0cf7]

    [ 0.094985] pci_bus 0000:00: resource 5 [io 0x0d00-0xffff]

    [ 0.094986] pci_bus 0000:00: resource 6 [mem 0x000a0000-0x000bffff]

    [ 0.094988] pci_bus 0000:00: resource 7 [mem 0x80000000-0xffffffff]

    [ 0.094990] pci_bus 0000:01: resource 0 [io 0x1000-0x1fff]

    [ 0.094992] pci_bus 0000:01: resource 1 [mem 0x80000000-0x801fffff]

    [ 0.094994] pci_bus 0000:01: resource 2 [mem 0x80200000-0x803fffff 64bit pref]

    [ 0.094996] pci_bus 0000:02: resource 0 [io 0xe000-0xefff]

    [ 0.094997] pci_bus 0000:02: resource 1 [mem 0xd0400000-0xd04fffff]

    [ 0.094999] pci_bus 0000:02: resource 2 [mem 0x80400000-0x805fffff 64bit pref]

    [ 0.095006] pci_bus 0000:03: resource 4 [io 0x0000-0x0cf7]

    [ 0.095007] pci_bus 0000:03: resource 5 [io 0x0d00-0xffff]

    [ 0.095009] pci_bus 0000:03: resource 6 [mem 0x000a0000-0x000bffff]

    [ 0.095011] pci_bus 0000:03: resource 7 [mem 0x80000000-0xffffffff]

    [ 0.095047] NET: Registered protocol family 2

    [ 0.095209] TCP established hash table entries: 16384 (order: 6, 262144 bytes)

    [ 0.095343] TCP bind hash table entries: 16384 (order: 6, 262144 bytes)

    [ 0.095454] TCP: Hash tables configured (established 16384 bind 16384)

    [ 0.095504] TCP: reno registered

    [ 0.095509] UDP hash table entries: 1024 (order: 3, 32768 bytes)

    [ 0.095526] UDP-Lite hash table entries: 1024 (order: 3, 32768 bytes)

    [ 0.095600] NET: Registered protocol family 1

    [ 0.095611] pci 0000:00:02.0: Boot video device

    [ 0.118093] PCI: CLS 64 bytes, default 64

    [ 0.118146] Unpacking initramfs...

    [ 0.258102] Freeing initrd memory: 9008k freed

    [ 0.262544] Initialise system trusted keyring

    [ 0.262594] audit: initializing netlink socket (disabled)

    [ 0.262612] type=2000 audit(1378259626.261:1): initialized

    [ 0.282927] HugeTLB registered 2 MB page size, pre-allocated 0 pages

    [ 0.284217] VFS: Disk quotas dquot_6.5.2

    [ 0.284254] Dquot-cache hash table entries: 512 (order 0, 4096 bytes)

    [ 0.284586] msgmni has been set to 3922

    [ 0.284638] SELinux: Registering netfilter hooks

    [ 0.285079] alg: No test for stdrng (krng)

    [ 0.285085] NET: Registered protocol family 38

    [ 0.285089] Key type asymmetric registered

    [ 0.285091] Asymmetric key parser 'x509' registered

    [ 0.285092] Asymmetric key parser 'pefile' registered

    [ 0.285123] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 252)

    [ 0.285146] io scheduler noop registered

    [ 0.285148] io scheduler deadline registered

    [ 0.285172] io scheduler cfq registered (default)

    [ 0.285281] pcieport 0000:00:1c.0: irq 40 for MSI/MSI-X

    [ 0.285364] pcieport 0000:00:1c.1: irq 41 for MSI/MSI-X

    [ 0.285452] pcieport 0000:00:1c.0: Signaling PME through PCIe PME interrupt

    [ 0.285456] pcie_pme 0000:00:1c.0:pcie01: service driver pcie_pme loaded

    [ 0.285471] pcieport 0000:00:1c.1: Signaling PME through PCIe PME interrupt

    [ 0.285473] pci 0000:02:00.0: Signaling PME through PCIe PME interrupt

    [ 0.285476] pcie_pme 0000:00:1c.1:pcie01: service driver pcie_pme loaded

    [ 0.285489] pci_hotplug: PCI Hot Plug PCI Core version: 0.5

    [ 0.285515] pciehp 0000:00:1c.0:pcie04: HPC vendor_id 8086 device_id 27d0 ss_vid 8086 ss_did d612

    [ 0.285538] pciehp 0000:00:1c.0:pcie04: service driver pciehp loaded

    [ 0.285547] pciehp 0000:00:1c.1:pcie04: HPC vendor_id 8086 device_id 27d2 ss_vid 8086 ss_did d612

    [ 0.285567] pciehp 0000:00:1c.1:pcie04: service driver pciehp loaded

    [ 0.285571] pciehp: PCI Express Hot Plug Controller Driver version: 0.4

    [ 0.285633] intel_idle: does not run on family 6 model 23

    [ 0.285704] input: Power Button as /devices/LNXSYSTM:00/device:00/PNP0C0C:00/input/input0

    [ 0.285709] ACPI: Power Button [PWRB]

    [ 0.285749] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input1

    [ 0.285751] ACPI: Power Button [PWRF]

    [ 0.285811] ACPI: Requesting acpi_cpufreq

    [ 0.286775] tsc: Marking TSC unstable due to TSC halts in idle

    [ 0.286783] ACPI: acpi_idle registered with cpuidle

    [ 0.288173] GHES: HEST is not enabled!

    [ 0.288232] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled

    [ 0.308725] 00:05: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A

    [ 0.309116] Non-volatile memory driver v1.3

    [ 0.309118] Linux agpgart interface v0.103

    [ 0.309177] agpgart-intel 0000:00:00.0: Intel G41 Chipset

    [ 0.309236] agpgart-intel 0000:00:00.0: detected gtt size: 2097152K total, 262144K mappable

    [ 0.310045] agpgart-intel 0000:00:00.0: detected 32768K stolen memory

    [ 0.310160] agpgart-intel 0000:00:00.0: AGP aperture is 256M @ 0xc0000000

    [ 0.310810] loop: module loaded

    [ 0.310883] ata_piix 0000:00:1f.1: version 2.13

    [ 0.310979] ata_piix 0000:00:1f.1: setting latency timer to 64

    [ 0.311205] scsi0 : ata_piix

    [ 0.311510] scsi1 : ata_piix

    [ 0.311771] ata1: PATA max UDMA/100 cmd 0x1f0 ctl 0x3f6 bmdma 0xf0f0 irq 14

    [ 0.311773] ata2: PATA max UDMA/100 cmd 0x170 ctl 0x376 bmdma 0xf0f8 irq 15

    [ 0.311814] ata2: port disabled--ignoring

    [ 0.311816] ata_piix 0000:00:1f.2: MAP [

    [ 0.311818] P0 P2 P1 P3 ]

    [ 0.311839] ata_piix 0000:00:1f.2: setting latency timer to 64

    [ 0.312132] scsi2 : ata_piix

    [ 0.312406] scsi3 : ata_piix

    [ 0.312711] ata3: SATA max UDMA/133 cmd 0xf0e0 ctl 0xf0d0 bmdma 0xf0a0 irq 19

    [ 0.312713] ata4: SATA max UDMA/133 cmd 0xf0c0 ctl 0xf0b0 bmdma 0xf0a8 irq 19

    [ 0.312765] libphy: Fixed MDIO Bus: probed

    [ 0.312885] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver

    [ 0.312887] ehci-pci: EHCI PCI platform driver

    [ 0.312940] ehci-pci 0000:00:1d.7: setting latency timer to 64

    [ 0.312949] ehci-pci 0000:00:1d.7: EHCI Host Controller

    [ 0.312985] ehci-pci 0000:00:1d.7: new USB bus registered, assigned bus number 1

    [ 0.312998] ehci-pci 0000:00:1d.7: debug port 1

    [ 0.316899] ehci-pci 0000:00:1d.7: cache line size of 64 is not supported

    [ 0.316911] ehci-pci 0000:00:1d.7: irq 23, io mem 0xd0504000

    [ 0.322015] ehci-pci 0000:00:1d.7: USB 2.0 started, EHCI 1.00

    [ 0.322059] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002

    [ 0.322063] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1

    [ 0.322066] usb usb1: Product: EHCI Host Controller

    [ 0.322069] usb usb1: Manufacturer: Linux 3.10.10-200.fc19.x86_64 ehci_hcd

    [ 0.322072] usb usb1: SerialNumber: 0000:00:1d.7

    [ 0.322204] hub 1-0:1.0: USB hub found

    [ 0.322209] hub 1-0:1.0: 8 ports detected

    [ 0.322327] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver

    [ 0.322336] uhci_hcd: USB Universal Host Controller Interface driver

    [ 0.322382] uhci_hcd 0000:00:1d.0: setting latency timer to 64

    [ 0.322385] uhci_hcd 0000:00:1d.0: UHCI Host Controller

    [ 0.322418] uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 2

    [ 0.322438] uhci_hcd 0000:00:1d.0: irq 23, io base 0x0000f080

    [ 0.322463] usb usb2: New USB device found, idVendor=1d6b, idProduct=0001

    [ 0.322465] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1

    [ 0.322467] usb usb2: Product: UHCI Host Controller

    [ 0.322469] usb usb2: Manufacturer: Linux 3.10.10-200.fc19.x86_64 uhci_hcd

    [ 0.322471] usb usb2: SerialNumber: 0000:00:1d.0

    [ 0.322539] hub 2-0:1.0: USB hub found

    [ 0.322542] hub 2-0:1.0: 2 ports detected

    [ 0.322634] uhci_hcd 0000:00:1d.1: setting latency timer to 64

    [ 0.322637] uhci_hcd 0000:00:1d.1: UHCI Host Controller

    [ 0.322668] uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 3

    [ 0.322689] uhci_hcd 0000:00:1d.1: irq 19, io base 0x0000f060

    [ 0.322714] usb usb3: New USB device found, idVendor=1d6b, idProduct=0001

    [ 0.322717] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1

    [ 0.322718] usb usb3: Product: UHCI Host Controller

    [ 0.322720] usb usb3: Manufacturer: Linux 3.10.10-200.fc19.x86_64 uhci_hcd

    [ 0.322722] usb usb3: SerialNumber: 0000:00:1d.1

    [ 0.322786] hub 3-0:1.0: USB hub found

    [ 0.322789] hub 3-0:1.0: 2 ports detected

    [ 0.322880] uhci_hcd 0000:00:1d.2: setting latency timer to 64

    [ 0.322883] uhci_hcd 0000:00:1d.2: UHCI Host Controller

    [ 0.322922] uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 4

    [ 0.322949] uhci_hcd 0000:00:1d.2: irq 18, io base 0x0000f040

    [ 0.322975] usb usb4: New USB device found, idVendor=1d6b, idProduct=0001

    [ 0.322977] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1

    [ 0.322979] usb usb4: Product: UHCI Host Controller

    [ 0.322980] usb usb4: Manufacturer: Linux 3.10.10-200.fc19.x86_64 uhci_hcd

    [ 0.322982] usb usb4: SerialNumber: 0000:00:1d.2

    [ 0.323049] hub 4-0:1.0: USB hub found

    [ 0.323053] hub 4-0:1.0: 2 ports detected

    [ 0.323144] uhci_hcd 0000:00:1d.3: setting latency timer to 64

    [ 0.323147] uhci_hcd 0000:00:1d.3: UHCI Host Controller

    [ 0.323184] uhci_hcd 0000:00:1d.3: new USB bus registered, assigned bus number 5

    [ 0.323211] uhci_hcd 0000:00:1d.3: irq 16, io base 0x0000f020

    [ 0.323234] usb usb5: New USB device found, idVendor=1d6b, idProduct=0001

    [ 0.323236] usb usb5: New USB device strings: Mfr=3, Product=2, SerialNumber=1

    [ 0.323238] usb usb5: Product: UHCI Host Controller

    [ 0.323240] usb usb5: Manufacturer: Linux 3.10.10-200.fc19.x86_64 uhci_hcd

    [ 0.323242] usb usb5: SerialNumber: 0000:00:1d.3

    [ 0.323307] hub 5-0:1.0: USB hub found

    [ 0.323310] hub 5-0:1.0: 2 ports detected

    [ 0.323406] usbcore: registered new interface driver usbserial

    [ 0.323412] usbcore: registered new interface driver usbserial_generic

    [ 0.323418] usbserial: USB Serial support registered for generic

    [ 0.323451] i8042: PNP: PS/2 Controller [PNP0303:PS2K] at 0x60,0x64 irq 1

    [ 0.323452] i8042: PNP: PS/2 appears to have AUX port disabled, if this is incorrect please boot with i8042.nopnp

    [ 0.324040] serio: i8042 KBD port at 0x60,0x64 irq 1

    [ 0.324097] mousedev: PS/2 mouse device common for all mice

    [ 0.324228] rtc_cmos 00:08: RTC can wake from S4

    [ 0.324341] rtc_cmos 00:08: rtc core: registered rtc_cmos as rtc0

    [ 0.324363] rtc_cmos 00:08: alarms up to one month, y3k, 114 bytes nvram, hpet irqs

    [ 0.324419] device-mapper: uevent: version 1.0.3

    [ 0.324476] device-mapper: ioctl: 4.24.0-ioctl (2013-01-15) initialised: dm-devel@redhat.com

    [ 0.324539] cpuidle: using governor ladder

    [ 0.324575] cpuidle: using governor menu

    [ 0.324744] hidraw: raw HID events driver (C) Jiri Kosina

    [ 0.324819] usbcore: registered new interface driver usbhid

    [ 0.324821] usbhid: USB HID core driver

    [ 0.324840] drop_monitor: Initializing network drop monitor service

    [ 0.324910] ip_tables: (C) 2000-2006 Netfilter Core Team

    [ 0.324936] TCP: cubic registered

    [ 0.324938] Initializing XFRM netlink socket

    [ 0.325035] NET: Registered protocol family 10

    [ 0.325205] mip6: Mobile IPv6

    [ 0.325208] NET: Registered protocol family 17

    [ 0.325405] PM: Hibernation image not present or could not be loaded.

    [ 0.325406] Loading compiled-in X.509 certificates

    [ 0.326319] Loaded X.509 cert 'Fedora kernel signing key: 6a933b96f346c52479a9131f6ae6ddd39f993920'

    [ 0.326328] registered taskstats version 1

    [ 0.326672] Magic number: 13:758:861

    [ 0.326752] rtc_cmos 00:08: setting system clock to 2013-09-04 01:53:47 UTC (1378259627)

    [ 0.344988] input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input2

    [ 0.477376] ata4.00: ATA-8: ST500DM002-1BC142, JC4B, max UDMA/133

    [ 0.477381] ata4.00: 976773168 sectors, multi 16: LBA48 NCQ (depth 0/32)

    [ 0.483366] ata4.00: configured for UDMA/133

    [ 0.483498] scsi 3:0:0:0: Direct-Access ATA ST500DM002-1BC14 JC4B PQ: 0 ANSI: 5

    [ 0.483637] sd 3:0:0:0: [sda] 976773168 512-byte logical blocks: (500 GB/465 GiB)

    [ 0.483653] sd 3:0:0:0: Attached scsi generic sg0 type 0

    [ 0.483680] sd 3:0:0:0: [sda] Write Protect is off

    [ 0.483682] sd 3:0:0:0: [sda] Mode Sense: 00 3a 00 00

    [ 0.483711] sd 3:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA

    [ 0.530707] sda: sda1 sda2 sda3 sda4 < sda5 >

    [ 0.531076] sd 3:0:0:0: [sda] Attached SCSI disk

    [ 0.531755] Freeing unused kernel memory: 1412k freed

    [ 0.532147] Write protecting the kernel read-only data: 12288k

    [ 0.535780] Freeing unused kernel memory: 1736k freed

    [ 0.538852] Freeing unused kernel memory: 1284k freed

    [ 0.541909] systemd[1]: RTC configured in localtime, applying delta of 330 minutes to system time.

    [ 0.542971] systemd[1]: systemd 204 running in system mode. (+PAM +LIBWRAP +AUDIT +SELINUX +IMA +SYSVINIT +LIBCRYPTSETUP +GCRYPT +ACL +XZ)

    [ 0.543088] systemd[1]: Running in initial RAM disk.

    [ 0.543200] systemd[1]: Set hostname to <localhost.localdomain>.

    [ 0.548341] systemd[1]: Expecting device dev-disk-by\x2duuid-7ebe2fb4\x2d4a29\x2d49e3\x2d9bf8\x2d4e91dea84a0d.device...

    [ 0.548354] systemd[1]: Expecting device dev-mapper-fedora\x2droot.device...

    [ 0.548363] systemd[1]: Expecting device dev-mapper-fedora\x2dswap.device...

    [ 0.548372] systemd[1]: Starting Timers.

    [ 0.548382] systemd[1]: Reached target Timers.

    [ 0.548436] systemd[1]: Starting udev Kernel Socket.

    [ 0.548466] systemd[1]: Listening on udev Kernel Socket.

    [ 0.548508] systemd[1]: Starting udev Control Socket.

    [ 0.548535] systemd[1]: Listening on udev Control Socket.

    [ 0.548544] systemd[1]: Starting Journal Socket.

    [ 0.548590] systemd[1]: Listening on Journal Socket.

    [ 0.548744] systemd[1]: Starting dracut cmdline hook...

    [ 0.549197] systemd[1]: Starting Sockets.

    [ 0.549209] systemd[1]: Reached target Sockets.

    [ 0.549218] systemd[1]: Starting Journal Service...

    [ 0.549636] systemd[1]: Started Journal Service.

    [ 0.550822] systemd[1]: Started Load Kernel Modules.

    [ 0.550835] systemd[1]: Starting Swap.

    [ 0.550847] systemd[1]: Reached target Swap.

    [ 0.550856] systemd[1]: Starting Local File Systems.

    [ 0.550865] systemd[1]: Reached target Local File Systems.

    [ 0.658200] systemd-udevd[146]: starting version 204

    [ 0.705773] [drm] Initialized drm 1.1.0 20060810

    [ 0.721996] [drm] Memory usable by graphics device = 2048M

    [ 0.722039] i915 0000:00:02.0: setting latency timer to 64

    [ 0.745815] i915 0000:00:02.0: irq 42 for MSI/MSI-X

    [ 0.745824] [drm] Supports vblank timestamp caching Rev 1 (10.10.2010).

    [ 0.745825] [drm] Driver supports precise vblank timestamp query.

    [ 0.745869] vgaarb: device changed decodes: PCI:0000:00:02.0,olddecodes=io+mem,decodes=io+mem:owns=io+mem

    [ 0.847015] [drm] GMBUS [i915 gmbus dpb] timed out, falling back to bit banging on pin 5

    [ 0.857070] fbcon: inteldrmfb (fb0) is primary device

    [ 0.884027] usb 5-2: new low-speed USB device number 2 using uhci_hcd

    [ 0.913025] Console: switching to colour frame buffer device 128x48

    [ 0.914830] i915 0000:00:02.0: fb0: inteldrmfb frame buffer device

    [ 0.914832] i915 0000:00:02.0: registered panic notifier

    [ 0.914906] ACPI Exception: AE_NOT_FOUND, Evaluating _DOD (20130328/video-1262)

    [ 0.914913] ACPI: Video Device [GFX0] (multi-head: no rom: yes post: no)

    [ 0.915394] input: Video Bus as /devices/LNXSYSTM:00/device:00/PNP0A08:00/LNXVIDEO:00/input/input3

    [ 0.915456] [drm] Initialized i915 1.6.0 20080730 for 0000:00:02.0 on minor 0

    [ 1.046243] usb 5-2: New USB device found, idVendor=046d, idProduct=c018

    [ 1.046247] usb 5-2: New USB device strings: Mfr=1, Product=2, SerialNumber=0

    [ 1.046249] usb 5-2: Product: USB Optical Mouse

    [ 1.046251] usb 5-2: Manufacturer: Logitech

    [ 1.062531] input: Logitech USB Optical Mouse as /devices/pci0000:00/0000:00:1d.3/usb5/5-2/5-2:1.0/input/input4

    [ 1.062628] hid-generic 0003:046D:C018.0001: input,hidraw0: USB HID v1.11 Mouse [Logitech USB Optical Mouse] on usb-0000:00:1d.3-2/input0

    [ 1.285645] bio: create slab <bio-1> at 1

    [ 1.601030] EXT4-fs (dm-1): mounted filesystem with ordered data mode. Opts: (null)

    [ 1.723101] systemd-journald[58]: Received SIGTERM

    [ 2.163794] type=1404 audit(1378239829.336:2): enforcing=1 old_enforcing=0 auid=4294967295 ses=4294967295

    [ 2.438637] SELinux: 2048 avtab hash slots, 94943 rules.

    [ 2.452225] SELinux: 2048 avtab hash slots, 94943 rules.

    [ 2.846949] SELinux: 8 users, 82 roles, 4533 types, 257 bools, 1 sens, 1024 cats

    [ 2.846954] SELinux: 83 classes, 94943 rules

    [ 2.852032] SELinux: Completing initialization.

    [ 2.852035] SELinux: Setting up existing superblocks.

    [ 2.852043] SELinux: initialized (dev sysfs, type sysfs), uses genfs_contexts

    [ 2.852048] SELinux: initialized (dev rootfs, type rootfs), uses genfs_contexts

    [ 2.852061] SELinux: initialized (dev bdev, type bdev), uses genfs_contexts

    [ 2.852066] SELinux: initialized (dev proc, type proc), uses genfs_contexts

    [ 2.852076] SELinux: initialized (dev tmpfs, type tmpfs), uses transition SIDs

    [ 2.852100] SELinux: initialized (dev devtmpfs, type devtmpfs), uses transition SIDs

    [ 2.852822] SELinux: initialized (dev sockfs, type sockfs), uses task SIDs

    [ 2.852827] SELinux: initialized (dev debugfs, type debugfs), uses genfs_contexts

    [ 2.854581] SELinux: initialized (dev pipefs, type pipefs), uses task SIDs

    [ 2.854589] SELinux: initialized (dev anon_inodefs, type anon_inodefs), uses genfs_contexts

    [ 2.854592] SELinux: initialized (dev devpts, type devpts), uses transition SIDs

    [ 2.854613] SELinux: initialized (dev hugetlbfs, type hugetlbfs), uses transition SIDs

    [ 2.854620] SELinux: initialized (dev mqueue, type mqueue), uses transition SIDs

    [ 2.854628] SELinux: initialized (dev selinuxfs, type selinuxfs), uses genfs_contexts

    [ 2.854649] SELinux: initialized (dev sysfs, type sysfs), uses genfs_contexts

    [ 2.855261] SELinux: initialized (dev securityfs, type securityfs), uses genfs_contexts

    [ 2.855263] SELinux: initialized (dev tmpfs, type tmpfs), uses transition SIDs

    [ 2.855269] SELinux: initialized (dev tmpfs, type tmpfs), uses transition SIDs

    [ 2.855342] SELinux: initialized (dev tmpfs, type tmpfs), uses transition SIDs

    [ 2.855374] SELinux: initialized (dev cgroup, type cgroup), uses genfs_contexts

    [ 2.855385] SELinux: initialized (dev pstore, type pstore), uses genfs_contexts

    [ 2.855387] SELinux: initialized (dev cgroup, type cgroup), uses genfs_contexts

    [ 2.855396] SELinux: initialized (dev cgroup, type cgroup), uses genfs_contexts

    [ 2.855435] SELinux: initialized (dev cgroup, type cgroup), uses genfs_contexts

    [ 2.855449] SELinux: initialized (dev cgroup, type cgroup), uses genfs_contexts

    [ 2.855455] SELinux: initialized (dev cgroup, type cgroup), uses genfs_contexts

    [ 2.855460] SELinux: initialized (dev cgroup, type cgroup), uses genfs_contexts

    [ 2.855464] SELinux: initialized (dev cgroup, type cgroup), uses genfs_contexts

    [ 2.855478] SELinux: initialized (dev cgroup, type cgroup), uses genfs_contexts

    [ 2.855489] SELinux: initialized (dev dm-1, type ext4), uses xattr

    [ 2.871777] type=1403 audit(1378239830.044:3): policy loaded auid=4294967295 ses=4294967295

    [ 2.875984] systemd[1]: Successfully loaded SELinux policy in 739.765ms.

    [ 3.006426] systemd[1]: RTC configured in localtime, applying delta of 330 minutes to system time.

    [ 3.031538] systemd[1]: Relabelled /dev and /run in 15.137ms.

    [ 3.455573] LVM: Logical Volume autoactivation enabled.

    [ 3.455578] LVM: Activation generator successfully completed.

    [ 4.201230] SELinux: initialized (dev autofs, type autofs), uses genfs_contexts

    [ 4.901925] SELinux: initialized (dev configfs, type configfs), uses genfs_contexts

    [ 4.903290] SELinux: initialized (dev tmpfs, type tmpfs), uses transition SIDs

    [ 4.903567] SELinux: initialized (dev hugetlbfs, type hugetlbfs), uses transition SIDs

    [ 5.258603] systemd-udevd[319]: starting version 204

    [ 5.769322] EXT4-fs (dm-1): re-mounted. Opts: (null)

    [ 5.831377] parport_pc 00:06: reported by Plug and Play ACPI

    [ 5.831478] parport0: PC-style at 0x378 (0x778), irq 5 [PCSPP,TRISTATE,EPP]

    [ 5.852513] r8169 Gigabit Ethernet driver 2.3LK-NAPI loaded

    [ 5.852726] r8169 0000:02:00.0: irq 43 for MSI/MSI-X

    [ 5.852879] r8169 0000:02:00.0 eth0: RTL8168d/8111d at 0xffffc900103ee000, 00:1c:c0:c0:bb:1e, XID 081000c0 IRQ 43

    [ 5.852882] r8169 0000:02:00.0 eth0: jumbo features [frames: 9200 bytes, tx checksumming: ko]

    [ 5.858941] snd_hda_intel 0000:00:1b.0: irq 44 for MSI/MSI-X

    [ 5.860964] intel_rng: Firmware space is locked read-only. If you can't or

    intel_rng: don't want to disable this in firmware setup, and if

    intel_rng: you are certain that your system has a functional

    intel_rng: RNG, try using the 'no_fwh_detect' option.

    [ 5.876597] ALSA sound/pci/hda/patch_realtek.c:414 SKU: Nid=0x1d sku_cfg=0x4014c601

    [ 5.876601] ALSA sound/pci/hda/patch_realtek.c:416 SKU: port_connectivity=0x1

    [ 5.876603] ALSA sound/pci/hda/patch_realtek.c:417 SKU: enable_pcbeep=0x1

    [ 5.876604] ALSA sound/pci/hda/patch_realtek.c:418 SKU: check_sum=0x00000004

    [ 5.876606] ALSA sound/pci/hda/patch_realtek.c:419 SKU: customization=0x000000c6

    [ 5.876607] ALSA sound/pci/hda/patch_realtek.c:420 SKU: external_amp=0x0

    [ 5.876609] ALSA sound/pci/hda/patch_realtek.c:421 SKU: platform_type=0x0

    [ 5.876610] ALSA sound/pci/hda/patch_realtek.c:422 SKU: swap=0x0

    [ 5.876611] ALSA sound/pci/hda/patch_realtek.c:423 SKU: override=0x1

    [ 5.876798] ALSA sound/pci/hda/hda_auto_parser.c:393 autoconfig: line_outs=1 (0x14/0x0/0x0/0x0/0x0) type:line

    [ 5.876800] ALSA sound/pci/hda/hda_auto_parser.c:397 speaker_outs=0 (0x0/0x0/0x0/0x0/0x0)

    [ 5.876802] ALSA sound/pci/hda/hda_auto_parser.c:401 hp_outs=0 (0x0/0x0/0x0/0x0/0x0)

    [ 5.876803] ALSA sound/pci/hda/hda_auto_parser.c:402 mono: mono_out=0x0

    [ 5.876805] ALSA sound/pci/hda/hda_auto_parser.c:405 dig-out=0x1e/0x0

    [ 5.876806] ALSA sound/pci/hda/hda_auto_parser.c:406 inputs:

    [ 5.876993] ALSA sound/pci/hda/hda_auto_parser.c:410 Mic=0x18

    [ 5.876995] ALSA sound/pci/hda/hda_auto_parser.c:410 Line=0x1a

    [ 5.876997] ALSA sound/pci/hda/patch_realtek.c:486 realtek: No valid SSID, checking pincfg 0x4014c601 for NID 0x1d

    [ 5.876999] ALSA sound/pci/hda/patch_realtek.c:502 realtek: Enabling init ASM_ID=0xc601 CODEC_ID=10ec0888

    [ 5.897899] input: HDA Intel Line Out as /devices/pci0000:00/0000:00:1b.0/sound/card0/input5

    [ 5.898110] input: HDA Intel Line as /devices/pci0000:00/0000:00:1b.0/sound/card0/input6

    [ 5.898184] input: HDA Intel Mic as /devices/pci0000:00/0000:00:1b.0/sound/card0/input7

    [ 5.898716] ACPI Warning: 0x0000000000000480-0x00000000000004af SystemIO conflicts with Region \_SB_.PCI0.SBRG.P10L 1 (20130328/utaddress-251)

    [ 5.898722] ACPI Warning: 0x0000000000000480-0x00000000000004af SystemIO conflicts with Region \_SB_.PCI0.SBRG.JP10 2 (20130328/utaddress-251)

    [ 5.898725] ACPI Warning: 0x0000000000000480-0x00000000000004af SystemIO conflicts with Region \_SB_.PCI0.SBRG.GPIM 3 (20130328/utaddress-251)

    [ 5.898728] ACPI: If an ACPI driver is available for this device, you should use it instead of the native driver

    [ 5.899305] i801_smbus 0000:00:1f.3: SMBus using PCI Interrupt

    [ 5.900794] leds_ss4200: no LED devices found

    [ 5.902218] microcode: CPU0 sig=0x1067a, pf=0x1, revision=0xa07

    [ 5.946967] ppdev: user-space parallel port driver

    [ 5.958088] iTCO_vendor_support: vendor-support=0

    [ 5.960660] iTCO_wdt: Intel TCO WatchDog Timer Driver v1.10

    [ 5.960699] iTCO_wdt: Found a ICH7 or ICH7R TCO device (Version=2, TCOBASE=0x0860)

    [ 5.961896] iTCO_wdt: initialized. heartbeat=30 sec (nowayout=0)

    [ 5.974123] systemd-udevd[328]: renamed network interface eth0 to p33p1

    [ 6.159382] microcode: CPU0 sig=0x1067a, pf=0x1, revision=0xa07

    [ 6.160378] microcode: CPU0 updated to revision 0xa0b, date = 2010-09-28

    [ 6.164101] microcode: CPU1 sig=0x1067a, pf=0x1, revision=0xa07

    [ 6.164200] microcode: CPU1 sig=0x1067a, pf=0x1, revision=0xa07

    [ 6.165076] microcode: CPU1 updated to revision 0xa0b, date = 2010-09-28

    [ 6.169094] microcode: Microcode Update Driver: v2.00 <tigran@aivazian.fsnet.co.uk>, Peter Oruba

    [ 6.904843] Adding 2113532k swap on /dev/mapper/fedora-swap. Priority:-1 extents:1 across:2113532k FS

    [ 9.288513] EXT4-fs (sda3): mounted filesystem with ordered data mode. Opts: (null)

    [ 9.552158] SELinux: initialized (dev sda3, type ext4), uses xattr

    [ 9.955459] EXT4-fs (dm-2): mounted filesystem with ordered data mode. Opts: (null)

    [ 9.955468] SELinux: initialized (dev dm-2, type ext4), uses xattr

    [ 10.104848] type=1305 audit(1378239837.277:4): audit_pid=394 old=0 auid=4294967295 ses=4294967295

    subj=system_u:system_r:auditd_t:s0 res=1

    [ 10.934789] systemd[1]: Unit rngd.service entered failed state.

    [ 12.305818] systemd-logind[420]: Watching system buttons on /dev/input/event1 (Power Button)

    [ 12.305897] systemd-logind[420]: Watching system buttons on /dev/input/event3 (Video Bus)

    [ 12.305970] systemd-logind[420]: Watching system buttons on /dev/input/event0 (Power Button)

    [ 20.584482] ip6_tables: (C) 2000-2006 Netfilter Core Team

    [ 20.614306] Ebtables v2.0 registered

    [ 20.658572] nf_conntrack version 0.5.0 (16384 buckets, 65536 max)

    [ 20.939389] Bluetooth: Core ver 2.16

    [ 20.939467] NET: Registered protocol family 31

    [ 20.939469] Bluetooth: HCI device and connection manager initialized

    [ 20.939480] Bluetooth: HCI socket layer initialized

    [ 20.939482] Bluetooth: L2CAP socket layer initialized

    [ 20.939488] Bluetooth: SCO socket layer initialized

    [ 21.006738] Bluetooth: BNEP (Ethernet Emulation) ver 1.3

    [ 21.006742] Bluetooth: BNEP filters: protocol multicast

    [ 21.006754] Bluetooth: BNEP socket layer initialized

    [ 21.085337] r8169 0000:02:00.0 p33p1: link down

    [ 21.085349] r8169 0000:02:00.0 p33p1: link down

    [ 21.085478] IPv6: ADDRCONF(NETDEV_UP): p33p1: link is not ready

    [ 23.127488] r8169 0000:02:00.0 p33p1: link up

    [ 23.127501] IPv6: ADDRCONF(NETDEV_CHANGE): p33p1: link becomes ready

    [ 30.603703] fuse init (API version 7.22)

    [ 30.613423] SELinux: initialized (dev fuse, type fuse), uses genfs_contexts

    [ 21.577]

    X.Org X Server 1.14.2

    Release Date: 2013-06-25

    [ 21.577] X Protocol Version 11, Revision 0

    [ 21.577] Build Operating System: 2.6.32-358.14.1.el6.x86_64

    [ 21.577] Current Operating System: Linux localhost.localdomain 3.10.10-200.fc19.x86_64 #1 SMP Thu Aug 29 19:05:45 UTC 2013 x86_64

    [ 21.577] Kernel command line: BOOT_IMAGE=/vmlinuz-3.10.10-200.fc19.x86_64 root=/dev/mapper/fedora-root ro rd.lvm.lv=fedora/swap rd.md=0 rd.dm=0 vconsole.keymap=us rd.luks=0 vconsole.font=latarcyrheb-sun16 rd.lvm.lv=fedora/root rhgb quiet LANG=en_US.UTF-8

    [ 21.578] Build Date: 30 July 2013 06:25:50AM

    [ 21.578] Build ID: xorg-x11-server 1.14.2-9.fc19

    [ 21.578] Current version of pixman: 0.30.0

    [ 21.578] Before reporting problems, check http://wiki.x.org

    to make sure that you have the latest version.

    [ 21.578] Markers: (--) probed, (**) from config file, (==) default setting,

    (++) from command line, (!!) notice, (II) informational,

    (WW) warning, (EE) error, (NI) not implemented, (??) unknown.

    [ 21.578] (==) Log file: "/var/log/Xorg.0.log", Time: Wed Sep 4 01:54:08 2013

    [ 21.589] (==) Using config directory: "/etc/X11/xorg.conf.d"

    [ 21.589] (==) Using system config directory "/usr/share/X11/xorg.conf.d"

    [ 21.589] (==) No Layout section. Using the first Screen section.

    [ 21.589] (==) No screen section available. Using defaults.

    [ 21.589] (**) |-->Screen "Default Screen Section" (0)

    [ 21.589] (**) | |-->Monitor "<default monitor>"

    [ 21.589] (==) No monitor specified for screen "Default Screen Section".

    Using a default monitor configuration.

    [ 21.589] (==) Automatically adding devices

    [ 21.589] (==) Automatically enabling devices

    [ 21.589] (==) Automatically adding GPU devices

    [ 21.589] (==) FontPath set to:

    catalogue:/etc/X11/fontpath.d,

    built-ins

    [ 21.589] (==) ModulePath set to "/usr/lib64/xorg/modules"

    [ 21.589] (II) The server relies on udev to provide the list of input devices.

    If no devices become available, reconfigure udev or disable AutoAddDevices.

    [ 21.589] (II) Loader magic: 0x800d00

    [ 21.589] (II) Module ABI versions:

    [ 21.589] X.Org ANSI C Emulation: 0.4

    [ 21.589] X.Org Video Driver: 14.1

    [ 21.589] X.Org XInput driver : 19.2

    [ 21.589] X.Org Server Extension : 7.0

    [ 21.589] (II) xfree86: Adding drm device (/dev/dri/card0)

    [ 21.591] (--) PCI:*(0:0:2:0) 8086:2e32:8086:d612 rev 3, Mem @ 0xd0000000/4194304, 0xc0000000/268435456, I/O @ 0x0000f140/8, BIOS @ 0x????????/131072

    [ 21.591] Initializing built-in extension Generic Event Extension

    [ 21.591] Initializing built-in extension SHAPE

    [ 21.591] Initializing built-in extension MIT-SHM

    [ 21.591] Initializing built-in extension XInputExtension

    [ 21.591] Initializing built-in extension XTEST

    [ 21.591] Initializing built-in extension BIG-REQUESTS

    [ 21.591] Initializing built-in extension SYNC

    [ 21.591] Initializing built-in extension XKEYBOARD

    [ 21.591] Initializing built-in extension XC-MISC

    [ 21.591] Initializing built-in extension XINERAMA

    [ 21.591] Initializing built-in extension XFIXES

    [ 21.591] Initializing built-in extension RENDER

    [ 21.591] Initializing built-in extension RANDR

    [ 21.591] Initializing built-in extension COMPOSITE

    [ 21.591] Initializing built-in extension DAMAGE

    [ 21.591] Initializing built-in extension MIT-SCREEN-SAVER

    [ 21.591] Initializing built-in extension DOUBLE-BUFFER

    [ 21.591] Initializing built-in extension RECORD

    [ 21.591] Initializing built-in extension DPMS

    [ 21.591] Initializing built-in extension X-Resource

    [ 21.591] Initializing built-in extension XVideo

    [ 21.591] Initializing built-in extension XVideo-MotionCompensation

    [ 21.591] Initializing built-in extension SELinux

    [ 21.591] Initializing built-in extension XFree86-VidModeExtension

    [ 21.591] Initializing built-in extension XFree86-DGA

    [ 21.591] Initializing built-in extension XFree86-DRI

    [ 21.591] Initializing built-in extension DRI2

    [ 21.591] (II) "glx" will be loaded by default.

    [ 21.591] (II) LoadModule: "dri2"

    [ 21.591] (II) Module "dri2" already built-in

    [ 21.591] (II) LoadModule: "glamoregl"

    [ 21.598] (II) Loading /usr/lib64/xorg/modules/libglamoregl.so

    [ 21.600] (II) Module glamoregl: vendor="X.Org Foundation"

    [ 21.600] compiled for 1.14.0, module version = 0.5.0

    [ 21.600] ABI class: X.Org ANSI C Emulation, version 0.4

    [ 21.600] (II) LoadModule: "glx"

    [ 21.600] (II) Loading /usr/lib64/xorg/modules/extensions/libglx.so

    [ 21.600] (II) Module glx: vendor="X.Org Foundation"

    [ 21.600] compiled for 1.14.2, module version = 1.0.0

    [ 21.600] ABI class: X.Org Server Extension, version 7.0

    [ 21.600] (==) AIGLX enabled

    [ 21.600] Loading extension GLX

    [ 21.600] (==) Matched intel as autoconfigured driver 0

    [ 21.600] (==) Matched intel as autoconfigured driver 1

    [ 21.600] (==) Matched vesa as autoconfigured driver 2

    [ 21.600] (==) Matched modesetting as autoconfigured driver 3

    [ 21.600] (==) Matched fbdev as autoconfigured driver 4

    [ 21.600] (==) Assigned the driver to the xf86ConfigLayout

    [ 21.600] (II) LoadModule: "intel"

    [ 21.600] (II) Loading /usr/lib64/xorg/modules/drivers/intel_drv.so

    [ 21.601] (II) Module intel: vendor="X.Org Foundation"

    [ 21.601] compiled for 1.14.2, module version = 2.21.12

    [ 21.601] Module class: X.Org Video Driver

    [ 21.601] ABI class: X.Org Video Driver, version 14.1

    [ 21.601] (II) LoadModule: "vesa"

    [ 21.601] (II) Loading /usr/lib64/xorg/modules/drivers/vesa_drv.so

    [ 21.601] (II) Module vesa: vendor="X.Org Foundation"

    [ 21.601] compiled for 1.14.0, module version = 2.3.2

    [ 21.601] Module class: X.Org Video Driver

    [ 21.601] ABI class: X.Org Video Driver, version 14.1

    [ 21.601] (II) LoadModule: "modesetting"

    [ 21.601] (II) Loading /usr/lib64/xorg/modules/drivers/modesetting_drv.so

    [ 21.601] (II) Module modesetting: vendor="X.Org Foundation"

    [ 21.601] compiled for 1.14.1, module version = 0.6.0

    [ 21.601] Module class: X.Org Video Driver

    [ 21.601] ABI class: X.Org Video Driver, version 14.1

    [ 21.601] (II) LoadModule: "fbdev"

    [ 21.601] (II) Loading /usr/lib64/xorg/modules/drivers/fbdev_drv.so

    [ 21.601] (II) Module fbdev: vendor="X.Org Foundation"

    [ 21.601] compiled for 1.14.0, module version = 0.4.3

    [ 21.601] Module class: X.Org Video Driver

    [ 21.601] ABI class: X.Org Video Driver, version 14.1

    [ 21.601] (II) intel: Driver for Intel Integrated Graphics Chipsets: i810,

    i810-dc100, i810e, i815, i830M, 845G, 854, 852GM/855GM, 865G, 915G,

    E7221 (i915), 915GM, 945G, 945GM, 945GME, Pineview GM, Pineview G,

    965G, G35, 965Q, 946GZ, 965GM, 965GME/GLE, G33, Q35, Q33, GM45,

    4 Series, G45/G43, Q45/Q43, G41, B43, B43, Clarkdale, Arrandale,

    Sandybridge Desktop (GT1), Sandybridge Desktop (GT2),

    Sandybridge Desktop (GT2+), Sandybridge Mobile (GT1),

    Sandybridge Mobile (GT2), Sandybridge Mobile (GT2+),

    Sandybridge Server, Ivybridge Mobile (GT1), Ivybridge Mobile (GT2),

    Ivybridge Desktop (GT1), Ivybridge Desktop (GT2), Ivybridge Server,

    Ivybridge Server (GT2), HD Graphics, HD Graphics 4600,

    Haswell Desktop (GT3), HD Graphics, HD Graphics 4600,

    Haswell Mobile (GT3), HD Graphics, HD Graphics P4600/P4700,

    Haswell Server (GT3), Haswell (GT1), Haswell (GT2), Haswell (GT3),

    HD Graphics, Haswell (GT2), Haswell (GT3), Haswell SDV Desktop (GT1),

    Haswell SDV Desktop (GT2), Haswell SDV Desktop (GT3),

    Haswell SDV Mobile (GT1), Haswell SDV Mobile (GT2),

    Haswell SDV Mobile (GT3), Haswell SDV Server (GT1),

    Haswell SDV Server (GT2), Haswell SDV Server (GT3),

    Haswell SDV (GT1), Haswell SDV (GT2), Haswell SDV (GT3),

    Haswell SDV (GT1), Haswell SDV (GT2), Haswell SDV (GT3),

    Haswell ULT Desktop (GT1), Haswell ULT Desktop (GT2),

    Iris(TM) Graphics 5100, HD Graphics, HD Graphics 4400,

    HD Graphics 5000, Haswell ULT Server (GT1), Haswell ULT Server (GT2),

    Iris(TM) Graphics 5100, Haswell ULT (GT1), Haswell ULT (GT2),

    Iris(TM) Graphics 5100, HD Graphics, HD Graphics 4200,

    Iris(TM) Graphics 5100, Haswell CRW Desktop (GT1), HD Graphics 4600,

    Iris(TM) Pro Graphics 5200, Haswell CRW Mobile (GT1),

    HD Graphics 4600, Iris(TM) Pro Graphics 5200,

    Haswell CRW Server (GT1), Haswell CRW Server (GT2),

    Iris(TM) Pro Graphics 5200, Haswell CRW (GT1), Haswell CRW (GT2),

    Iris(TM) Pro Graphics 5200, Haswell CRW (GT1), Haswell CRW (GT2),

    Iris(TM) Pro Graphics 5200, ValleyView PO board

    [ 21.603] (II) VESA: driver for VESA chipsets: vesa

    [ 21.603] (II) modesetting: Driver for Modesetting Kernel Drivers: kms

    [ 21.603] (II) FBDEV: driver for framebuffer: fbdev

    [ 21.603] (++) using VT number 1

     

    [ 21.604] (WW) Falling back to old probe method for vesa

    [ 21.604] (WW) Falling back to old probe method for modesetting

    [ 21.604] (WW) Falling back to old probe method for fbdev

    [ 21.604] (II) Loading sub module "fbdevhw"

    [ 21.604] (II) LoadModule: "fbdevhw"

    [ 21.604] (II) Loading /usr/lib64/xorg/modules/libfbdevhw.so

    [ 21.604] (II) Module fbdevhw: vendor="X.Org Foundation"

    [ 21.604] compiled for 1.14.2, module version = 0.0.2

    [ 21.604] ABI class: X.Org Video Driver, version 14.1

    [ 21.605] (II) intel(0): Creating default Display subsection in Screen section

    "Default Screen Section" for depth/fbbpp 24/32

    [ 21.605] (==) intel(0): Depth 24, (--) framebuffer bpp 32

    [ 21.605] (==) intel(0): RGB weight 888

    [ 21.605] (==) intel(0): Default visual is TrueColor

    [ 21.605] (--) intel(0): Integrated Graphics Chipset: Intel(R) G41

    [ 21.605] (**) intel(0): Relaxed fencing enabled

    [ 21.605] (**) intel(0): Wait on SwapBuffers? enabled

    [ 21.605] (**) intel(0): Triple buffering? enabled

    [ 21.605] (**) intel(0): Framebuffer tiled

    [ 21.605] (**) intel(0): Pixmaps tiled

    [ 21.605] (**) intel(0): 3D buffers tiled

    [ 21.605] (**) intel(0): SwapBuffers wait enabled

    [ 21.605] (==) intel(0): video overlay key set to 0x101fe

    [ 21.648] (II) intel(0): Output VGA1 has no monitor section

    [ 21.650] (II) intel(0): Output HDMI1 has no monitor section

    [ 21.650] (II) intel(0): Output DP1 has no monitor section

    [ 21.681] (II) intel(0): EDID for output VGA1

    [ 21.681] (II) intel(0): Printing probed modes for output VGA1

    [ 21.681] (II) intel(0): Modeline "1024x768"x60.0 65.00 1024 1048 1184 1344 768 771 777 806 -hsync -vsync (48.4 kHz e)

    [ 21.681] (II) intel(0): Modeline "800x600"x60.3 40.00 800 840 968 1056 600 601 605 628 +hsync +vsync (37.9 kHz e)

    [ 21.681] (II) intel(0): Modeline "800x600"x56.2 36.00 800 824 896 1024 600 601 603 625 +hsync +vsync (35.2 kHz e)

    [ 21.681] (II) intel(0): Modeline "848x480"x60.0 33.75 848 864 976 1088 480 486 494 517 +hsync +vsync (31.0 kHz e)

    [ 21.681] (II) intel(0): Modeline "640x480"x59.9 25.18 640 656 752 800 480 489 492 525 -hsync -vsync (31.5 kHz e)

    [ 21.683] (II) intel(0): EDID for output HDMI1

    [ 21.683] (II) intel(0): EDID for output DP1

    [ 21.683] (II) intel(0): Output VGA1 connected

    [ 21.683] (II) intel(0): Output HDMI1 disconnected

    [ 21.683] (II) intel(0): Output DP1 disconnected

    [ 21.683] (II) intel(0): Using exact sizes for initial modes

    [ 21.683] (II) intel(0): Output VGA1 using initial mode 1024x768 +0+0

    [ 21.683] (II) intel(0): Using default gamma of (1.0, 1.0, 1.0) unless otherwise stated.

    [ 21.683] (II) intel(0): Kernel page flipping support detected, enabling

    [ 21.683] (==) intel(0): DPI set to (96, 96)

    [ 21.683] (II) Loading sub module "fb"

    [ 21.683] (II) LoadModule: "fb"

    [ 21.683] (II) Loading /usr/lib64/xorg/modules/libfb.so

    [ 21.683] (II) Module fb: vendor="X.Org Foundation"

    [ 21.683] compiled for 1.14.2, module version = 1.0.0

    [ 21.683] ABI class: X.Org ANSI C Emulation, version 0.4

    [ 21.683] (II) Loading sub module "dri2"

    [ 21.683] (II) LoadModule: "dri2"

    [ 21.683] (II) Module "dri2" already built-in

    [ 21.683] (II) UnloadModule: "vesa"

    [ 21.683] (II) Unloading vesa

    [ 21.683] (II) UnloadModule: "modesetting"

    [ 21.683] (II) Unloading modesetting

    [ 21.683] (II) UnloadModule: "fbdev"

    [ 21.683] (II) Unloading fbdev

    [ 21.683] (II) UnloadSubModule: "fbdevhw"

    [ 21.683] (II) Unloading fbdevhw

    [ 21.683] (==) Depth 24 pixmap format is 32 bpp

    [ 21.683] (II) intel(0): [DRI2] Setup complete

    [ 21.683] (II) intel(0): [DRI2] DRI driver: i965

    [ 21.683] (II) intel(0): Allocated new frame buffer 1024x768 stride 4096, tiled

    [ 21.695] (II) UXA(0): Driver registered support for the following operations:

    [ 21.695] (II) solid

    [ 21.695] (II) copy

    [ 21.695] (II) composite (RENDER acceleration)

    [ 21.695] (II) put_image

    [ 21.695] (II) get_image

    [ 21.695] (==) intel(0): Backing store disabled

    [ 21.695] (==) intel(0): Silken mouse enabled

    [ 21.695] (II) intel(0): Initializing HW Cursor

    [ 21.695] (II) intel(0): RandR 1.2 enabled, ignore the following RandR disabled message.

    [ 21.695] (==) intel(0): DPMS enabled

    [ 21.695] (==) intel(0): Intel XvMC decoder enabled

    [ 21.695] (II) intel(0): Set up textured video

    [ 21.695] (II) intel(0): [XvMC] xvmc_vld driver initialized.

    [ 21.695] (II) intel(0): direct rendering: DRI2 Enabled

    [ 21.695] (==) intel(0): hotplug detection: "enabled"

    [ 21.706] (--) RandR disabled

    [ 21.711] (II) SELinux: Disabled by boolean

    [ 21.716] (II) AIGLX: enabled GLX_MESA_copy_sub_buffer

    [ 21.716] (II) AIGLX: enabled GLX_INTEL_swap_event

    [ 21.716] (II) AIGLX: enabled GLX_ARB_create_context

    [ 21.716] (II) AIGLX: enabled GLX_ARB_create_context_profile

    [ 21.716] (II) AIGLX: enabled GLX_EXT_create_context_es2_profile

    [ 21.716] (II) AIGLX: enabled GLX_SGI_swap_control and GLX_MESA_swap_control

    [ 21.716] (II) AIGLX: GLX_EXT_texture_from_pixmap backed by buffer objects

    [ 21.716] (II) AIGLX: Loaded and initialized i965

    [ 21.716] (II) GLX: Initialized DRI2 GL provider for screen 0

    [ 21.717] (II) intel(0): Setting screen physical size to 270 x 203

    [ 22.166] (II) config/udev: Adding input device Power Button (/dev/input/event1)

    [ 22.166] (**) Power Button: Applying InputClass "evdev keyboard catchall"

    [ 22.166] (**) Power Button: Applying InputClass "system-keyboard"

    [ 22.166] (II) LoadModule: "evdev"

    [ 22.166] (II) Loading /usr/lib64/xorg/modules/input/evdev_drv.so

    [ 22.167] (II) Module evdev: vendor="X.Org Foundation"

    [ 22.167] compiled for 1.14.2, module version = 2.8.1

    [ 22.167] Module class: X.Org XInput Driver

    [ 22.167] ABI class: X.Org XInput driver, version 19.1

    [ 22.167] (II) Using input driver 'evdev' for 'Power Button'

    [ 22.167] (**) Power Button: always reports core events

    [ 22.167] (**) evdev: Power Button: Device: "/dev/input/event1"

    [ 22.167] (--) evdev: Power Button: Vendor 0 Product 0x1

    [ 22.167] (--) evdev: Power Button: Found keys

    [ 22.167] (II) evdev: Power Button: Configuring as keyboard

    [ 22.167] (**) Option "config_info" "udev:/sys/devices/LNXSYSTM:00/LNXPWRBN:00/input/input1/event1"

    [ 22.167] (II) XINPUT: Adding extended input device "Power Button" (type: KEYBOARD, id 6)

    [ 22.167] (**) Option "xkb_rules" "evdev"

    [ 22.167] (**) Option "xkb_model" "pc104"

    [ 22.167] (**) Option "xkb_layout" "us"

    [ 22.214] (II) config/udev: Adding input device Video Bus (/dev/input/event3)

    [ 22.214] (**) Video Bus: Applying InputClass "evdev keyboard catchall"

    [ 22.214] (**) Video Bus: Applying InputClass "system-keyboard"

    [ 22.214] (II) Using input driver 'evdev' for 'Video Bus'

    [ 22.214] (**) Video Bus: always reports core events

    [ 22.214] (**) evdev: Video Bus: Device: "/dev/input/event3"

    [ 22.214] (--) evdev: Video Bus: Vendor 0 Product 0x6

    [ 22.214] (--) evdev: Video Bus: Found keys

    [ 22.214] (II) evdev: Video Bus: Configuring as keyboard

    [ 22.214] (**) Option "config_info" "udev:/sys/devices/LNXSYSTM:00/device:00/PNP0A08:00/LNXVIDEO:00/input/input3/event3"

    [ 22.214] (II) XINPUT: Adding extended input device "Video Bus" (type: KEYBOARD, id 7)

    [ 22.214] (**) Option "xkb_rules" "evdev"

    [ 22.214] (**) Option "xkb_model" "pc104"

    [ 22.214] (**) Option "xkb_layout" "us"

    [ 22.215] (II) config/udev: Adding input device Power Button (/dev/input/event0)

    [ 22.215] (**) Power Button: Applying InputClass "evdev keyboard catchall"

    [ 22.215] (**) Power Button: Applying InputClass "system-keyboard"

    [ 22.215] (II) Using input driver 'evdev' for 'Power Button'

    [ 22.215] (**) Power Button: always reports core events

    [ 22.215] (**) evdev: Power Button: Device: "/dev/input/event0"

    [ 22.215] (--) evdev: Power Button: Vendor 0 Product 0x1

    [ 22.215] (--) evdev: Power Button: Found keys

    [ 22.215] (II) evdev: Power Button: Configuring as keyboard

    [ 22.215] (**) Option "config_info" "udev:/sys/devices/LNXSYSTM:00/device:00/PNP0C0C:00/input/input0/event0"

    [ 22.215] (II) XINPUT: Adding extended input device "Power Button" (type: KEYBOARD, id 8)

    [ 22.215] (**) Option "xkb_rules" "evdev"

    [ 22.215] (**) Option "xkb_model" "pc104"

    [ 22.215] (**) Option "xkb_layout" "us"

    [ 22.215] (II) config/udev: Adding drm device (/dev/dri/card0)

    [ 22.216] (II) config/udev: Adding input device HDA Intel Line Out (/dev/input/event5)

    [ 22.216] (II) No input driver specified, ignoring this device.

    [ 22.216] (II) This device may have been added with another device file.

    [ 22.216] (II) config/udev: Adding input device HDA Intel Line (/dev/input/event6)

    [ 22.216] (II) No input driver specified, ignoring this device.

    [ 22.216] (II) This device may have been added with another device file.

    [ 22.216] (II) config/udev: Adding input device HDA Intel Mic (/dev/input/event7)

    [ 22.216] (II) No input driver specified, ignoring this device.

    [ 22.216] (II) This device may have been added with another device file.

    [ 22.216] (II) config/udev: Adding input device Logitech USB Optical Mouse (/dev/input/event4)

    [ 22.216] (**) Logitech USB Optical Mouse: Applying InputClass "evdev pointer catchall"

    [ 22.216] (II) Using input driver 'evdev' for 'Logitech USB Optical Mouse'

    [ 22.217] (**) Logitech USB Optical Mouse: always reports core events

    [ 22.217] (**) evdev: Logitech USB Optical Mouse: Device: "/dev/input/event4"

    [ 22.217] (--) evdev: Logitech USB Optical Mouse: Vendor 0x46d Product 0xc018

    [ 22.217] (--) evdev: Logitech USB Optical Mouse: Found 3 mouse buttons

    [ 22.217] (--) evdev: Logitech USB Optical Mouse: Found scroll wheel(s)

    [ 22.217] (--) evdev: Logitech USB Optical Mouse: Found relative axes

    [ 22.217] (--) evdev: Logitech USB Optical Mouse: Found x and y relative axes

    [ 22.217] (II) evdev: Logitech USB Optical Mouse: Configuring as mouse

    [ 22.217] (II) evdev: Logitech USB Optical Mouse: Adding scrollwheel support

    [ 22.217] (**) evdev: Logitech USB Optical Mouse: YAxisMapping: buttons 4 and 5

    [ 22.217] (**) evdev: Logitech USB Optical Mouse: EmulateWheelButton: 4, EmulateWheelInertia: 10, EmulateWheelTimeout: 200

    [ 22.217] (**) Option "config_info" "udev:/sys/devices/pci0000:00/0000:00:1d.3/usb5/5-2/5-2:1.0/input/input4/event4"

    [ 22.217] (II) XINPUT: Adding extended input device "Logitech USB Optical Mouse" (type: MOUSE, id 9)

    [ 22.217] (II) evdev: Logitech USB Optical Mouse: initialized for relative axes.

    [ 22.217] (**) Logitech USB Optical Mouse: (accel) keeping acceleration scheme 1

    [ 22.217] (**) Logitech USB Optical Mouse: (accel) acceleration profile 0

    [ 22.217] (**) Logitech USB Optical Mouse: (accel) acceleration factor: 2.000

    [ 22.217] (**) Logitech USB Optical Mouse: (accel) acceleration threshold: 4

    [ 22.217] (II) config/udev: Adding input device Logitech USB Optical Mouse (/dev/input/mouse0)

    [ 22.217] (II) No input driver specified, ignoring this device.

    [ 22.217] (II) This device may have been added with another device file.

    [ 22.220] (II) config/udev: Adding input device AT Translated Set 2 keyboard (/dev/input/event2)

    [ 22.220] (**) AT Translated Set 2 keyboard: Applying InputClass "evdev keyboard catchall"

    [ 22.220] (**) AT Translated Set 2 keyboard: Applying InputClass "system-keyboard"

    [ 22.220] (II) Using input driver 'evdev' for 'AT Translated Set 2 keyboard'

    [ 22.220] (**) AT Translated Set 2 keyboard: always reports core events

    [ 22.220] (**) evdev: AT Translated Set 2 keyboard: Device: "/dev/input/event2"

    [ 22.220] (--) evdev: AT Translated Set 2 keyboard: Vendor 0x1 Product 0x1

    [ 22.220] (--) evdev: AT Translated Set 2 keyboard: Found keys

    [ 22.220] (II) evdev: AT Translated Set 2 keyboard: Configuring as keyboard

    [ 22.220] (**) Option "config_info" "udev:/sys/devices/platform/i8042/serio0/input/input2/event2"

    [ 22.220] (II) XINPUT: Adding extended input device "AT Translated Set 2 keyboard" (type: KEYBOARD, id 10)

    [ 22.220] (**) Option "xkb_rules" "evdev"

    [ 22.220] (**) Option "xkb_model" "pc104"

    [ 22.220] (**) Option "xkb_layout" "us"

     

    Sep 03, 2013 - 01:42pm
  • Hi vbhardwaj7

     

    Sorry, my idea was bad. Could you please file a bug at bugs.freedesktop.org pasting all logs.

    Please follow this https://01.org/linuxgraphics/documentation/how-report-bugs-0

    And also don't forget to boot your machine with drm.debug=0xe to grab a good dmesg.

    Please assign the bug to me.

    Thanks,

    Rodrigo

    Sep 10, 2013 - 10:51am
  • Topic locked